*SALE*

RAD Industries Billet Intake Manifold Adapter

This is a Billet adapter plate to mate a 2JZ-GE lower intake manifold to 2JZ-GTE upper intake manifold. If you are building a NA-T setup on a 2JZ-GE engine and would like to simplify the look by eliminating the OEM intake manifold that crosses up and...

RAD Industries GTE Billet Upper Water Neck *Race Version

* RAD DAN SUPRA ITEM * The RAD Industries billet 2JZ-GTE + 1JZ-GTE RACE VERSION Upper water neck with -16 orb port. This product was designed with simplicity in mind while still maintaining the clean machined billet look in your engine bay...

RAD x KRC Power Steering PRO Kit

* RAD DAN SUPRA ITEM * Pro Series 3 (PS3) Pump with RAD-Ind 2JZ bracket (RAD_KRC_PSB) This kit is designed for the Pro driver or the guy building a serious level build that wants the best power steering available (Alternative BOSCH Kit) . The KRC pump...

RAD DAN Retro Tee | Gen 4

RADDEST Art By ZEROBRIANT [ @ZEROBRIANTEES ] 100% Cotton Fine jersey fabric. Extremely soft and comfortable!

[PN: RAD_10263] 2.75" Oversized Alternator Pulley

* RAD DAN SUPRA ITEM * This 2.75" pulley was designed to prevent over-spinning of the alternator. This will allow you to rev your engine to 9000rpm with an OEM crank pulley with no issues or rev to 8700rpm on an ATI under driver crank pulley. This pulley...

[PN: 101-0054] Link ECU Knock Sensor with Loom (KNSB)

DETAILS:   Donut style 8mm Knock Sensor prewired with 2.6m loom, flying leads.  Suitable to wire directly to Link ECU or use with the G4 Knocklink Visual Warning Light.    

[PN: 101-0053] Link ECU Knock Sensor (KNS)

DETAILS: Donut style 8mm hole Includes plug and pin kit   

[PN: 114-2000] Link ECU G4 KnockLink Kit - Includes Knock Sensor+Loom (G4KNLK)

DETAILS:   Kit includes the G4 KnockLink visual warning light and a knock sensor with loom. The KnockLink is a self-calibrating, visual knock warning tool. This kit is designed for tuning, street and race use.The G4 KnockLink is the only...

[PN: 114-1000] Link ECU KnockLink G4 (G4KNL)

DETAILS:   KnockLink is a self-calibrating, visual knock warning tool. The KnockLink is designed for tuning, street and race use. Will require a knock sensor to function (sold separately) or you can purchase the KnockLink Kit that includes the...

[PN: 105-1000] Link ECU KnockBlock G4+ (KNB)

DETAILS:   The G4+ KnockBlock is an essential tool for tuning and can aid in the early detection of incorrect ignition timing, lean air/fuel mixtures and mechanical issues. It is used it with ear buds, headphones or noise cancelling ear muffs and...

[PN: 110-0005] Link ECU Mounting bracket for G4+ & G4X Atom & Monsoon (MTB2)

[PN: 100-0113] Link ECU Mounting bracket for G4+ & G4X Fury, Xtreme, Storm, Force (MTB1)

[PN: 101-0016] Link ECU Boost Control Solenoid - 4 Port (4BCS)

DETAILS:   Thinking of turning up the boost to max? Then this 4 port boost control solenoid is perfect. It allows for precise boost control of up to 120PSI.4 port Boost control soldenoids are commonly used for big boost applications,...

[PN: 101-0103] Link ECU Trigger Wheel (TWS)

DETAILS:   Small Diameter Trigger wheel – Medium and Large sizes also available.  24 tooth 150mm diameter 40mm centre  

[PN: 101-0102] Link ECU Trigger Wheel (TWM)

DETAILS:   Medium Diameter Trigger wheel – Small and Large sizes also available. 24 tooth 175 diameter 40mm centre  

[PN: 101-0101] Link ECU Trigger Wheel (TWL)

DETAILS:   Large Diameter Trigger wheel – Small and Medium sizes also available. 60-2 tooth 200mm diameter 40mm centre

[PN: 101-0014] Link ECU Ballast Resistor (BAL6)

DETAILS:   For use with low-impedance injectors. Compatible with injectors with impedance between 2 and 6 Ohms. Please contact us if you are planning on using injectors with an impedance of less than 2 ohms.  Includes set of 6 x 4.7ohm...

[PN: 101-0013] Link ECU Ballast Resistor (BAL4)

DETAILS:   For use with low-impedance injectors. Compatible with injectors with impedance between 2 and 6 Ohms. Please contact us if you are planning on using injectors with an impedance of less than 2 ohms. Includes set of 4 x 4.7ohm...

[PN: 101-0012] Link ECU Ballast Resistor (BAL2)

DETAILS: For use with Low-Impedence Injectors. Includes set of 2 x 1 Ohm 50w resistors mounted to a heatsink. These are also sold in a single pack. Please contact us to ensure compatibility with your injectors.

[PN: 101-0011] Link ECU Ballast Resister (BAL)

DETAILS:   For use with Low-Impedence Injectors. Includes a single 1 Ohm 50W resistor mounted to a heatsink. Please contact us to ensure compatibility with your injectors.

[PN: 101-0291] Link ECU IGN1A - High Powered Inductive Smart Coil (Integrated Ignitor)

Link to User Guide     DETAILS:   High Power Inductive Coil with built-in ignitor. Produce 103 mJ per spark, with a longer spark duration (2.9 ms) than what you’d see with a capacitive discharge Built-in ignitor with...

[PN: 101-0044] Link ECU Three Channel Inductive Igniter (I3)

DETAILS:   This three channel igniter is suitable for electronic ignition applications.  Required when using coils that don't have inbuilt igniters.Common uses include: wasted spark on 6 cylinder engines, coil-per-plug setups on 3...

[PN: 101-0280] Link ECU Hall Effect Sensor Kit

DETAILS:   Hall effect sensor designed for use in applications where ferrous edge detection/near zero speed sensing is needed. They provide a sinking current output. Typical automotive applications include: Crank & Cam Signals...

[PN: 101-0025] Link ECU Crank Angle Sensor (CAS)

DETAILS:   Used in conjunction with a trigger wheel to measure crank angle, a vital measurement for engine operation. Can be used with almost any steel trigger wheel, see related products for our trigger wheel options.   FEATURES: ...

[PN: 101-0100] Link ECU Throttle Position Sensor (TPSCW/CCW)

DETAILS:   Throttle Position Sensor. Supports clockwise and counter-clockwise installations. 6 wire flying lead.  Wiring instructions are provided in the box. FEATURES: 8 mm D-Shaft Rotary Sensor Hall Effect non-contact technology...

[PN: 101-0146] Link ECU Exhaust Gas Temperature Probe (EGT)

DETAILS:   Extreme Duty Fast Response EGT Temperature Probe  Type K thermocouple probe Exposed sensing junction for fastest response Includes 316 SS adjustable compression fitting Stainless steel protected wires Designed for extreme...

[PN: 101-0034] Link ECU Ethanol Content Sensor (ECS)

DETAILS:   Looking to run flex-fuel? Then the Ethanol Content Sensor is a must have. The Ethanol Content Sensor measures the ratio of ethanol to petrol in a flex fuel vehicle. This sensor also measures fuel temperature. Compatible with all...

[PN: 101-0077] Link ECU Coolant Temperature Sensor (NTC12)

DETAILS: Includes Plug Kit - 2 way Bosch Style plug, terminals and boot M12 Thread

[PN: 101-0076] Link ECU Coolant Temperature Sensor (NTC1-8)

DETAILS: Includes 2-pin Deutsch DTM connector kit Aluminium and steel weld in mounting bosses available 1/8" NPT Thread  

[PN: 101-0050] Link ECU Mounting Boss Steel (IATBMS)

DETAILS:   Weld in Steel Boss. Bosch part. Suitable for mounting the IATB Inlet Air Temperature sensor and other sensors that mount via a Bosch style flange.  

[PN: 101-0049] Link ECU Mounting Boss Aluminium (IATBMA)

DETAILS:   Weld in Aluminium Boss. Bosch part. Suitable for mounting the IATB Inlet Air Temperature sensor and other sensors that mount via a Bosch style flange.  

[PN: 101-0048] Link ECU Air Temperature Sensor (IATB)

DETAILS: Includes Plug Kit - 2 way Bosch Style plug, terminals and boot Aluminium and steel weld in mounting bosses available (IATBMA & IATBMS)  

[PN: 101-0047] Link ECU Mounting Boss Steel (IAT1-8MS)

DETAILS:   Weld in steel boss, 1/8" NPT Thread. Suitable for mounting Intake air temperature (IAT1-8), Coolant Temperature sensors (NTC1-8) and other sensors that use 1/8" NPT Thread.

[PN: 101-0046] Link ECU Mounting Boss Aluminium (IAT1-8MA)

DETAILS:   Weld in Aluminium boss, 1/8" NPT Thread. Suitable for mounting Intake air temperature (IAT1-8), Coolant Temperature sensors (NTC1-8) and other sensors that use 1/8" NPT Thread.

[PN: 101-0045] Link ECU Air Temp Sensor (IAT1-8)

DETAILS: Includes 2-pin Deutsch DTM connector kit Aluminium and steel weld in mounting bosses available 1/8" NPT Thread  

[PN: 101-0199] Link ECU Adapter M10 x 1 Female to 1/8 BSP Male

DETAILS:   Stainless Steel thread adapter, M10 x 1 Female to 1/8 BSP Male, Adapts popular Bosch Metric Pressure Sensors to suit 1/8 BSP threaded ports.