Link ECU

[PN: 101-0300] Link ECUTerminated Engine Harness GM LS GEN3/4

Manuals Online Instruction Manual   DETAILS: Terminated Engine Harness to cover a wide range of GM LS Engine Variations. Please note that due to the large number of Engines supported it may...

[PN: 101-0301] Link ESU LS Stepper Adapter Harness

DETAILS: •    Intended for use with our terminated LS engine harness. Plug and play compatibility with GM LS IAC stepper motors. If you are planning to run a drive by cable...

[PN: 101-0302] Link ESU LS Map Adapter Harness

DETAILS: •    Intended for use with our terminated LS engine harness. Plug and play compatibility for Gen 3 LS map sensors

[PN: 101-0304] Link ECU LS DBW Adapter Loom

DETAILS: •    Intended for use with our terminated LS engine harness. Plug and play compatibility for Gen 4 LS DBW throttle bodies.  •    This...

[PN: 101-0305] Link ECU LS Gen 3 Knock Adapter Loom

DETAILS: •    Intended for use with our terminated LS engine harness. Plug and play compatibility with factory Gen 3 Knock Sensor loom (located in the valley).   ...

[PN: 101-0306] Link ECU LS Gen 4 Knock Adapter Loom

DETAILS: Intended for use with our terminated LS engine harness. Plug and play compatibility with Gen 4 Knock Sensors in factory location.       

[PN: 101-0307] Link ECU LS Gen 3 to Gen 4 Cam Sensor Conversion Harness

DETAILS: Adapter harness to run the Gen 4 front mounted under water pump Cam Sensor on the Gen 3 LS Engine.    

[PN: 101-0320] Link ECU Combined Pressure and Temperature Sensor (CPTS)

Technical Specs: See attached image.    DETAILS:   Two sensors in one - Combined 10 bar (145 psi) Liquid Pressure sensor and -40 to 140 deg C L Liquid Temperature sensor. ...

[PN: 101-0384] Link ECU TCC04 4 Channel EGT to CAN Module

Link TCC04 4 Channel EGT to CAN module, powered by CANchecked  The TCC04 EGT to CAN module allows you to connect up to four Type-K thermocouples and send the values via CAN bus and/or monitor...

[PN: 101-0388] Link ECU TCC08 8 Channel EGT to CAN Module

Link TCC08 8 Channel EGT to CAN module, powered by CANchecked The TCC08 EGT to CAN module allows you to connect up to eight Type-K thermocouples and send the values ​​via CAN bus and/or monitor them...

[PN: 105-1000] Link ECU KnockBlock G4+ (KNB)

DETAILS:   The G4+ KnockBlock is an essential tool for tuning and can aid in the early detection of incorrect ignition timing, lean air/fuel mixtures and mechanical issues. It is used it with...

[PN: 108-9000B] Link ECU G4X StormX ECU + Terminated LS Engine Harness Drive-by-Cable Bundle

Harness Manual Online Instruction Manual   DETAILS: The quickest, easiest, tidiest and most cost effective way to connect a Link ECU to your Drive-by-Cable LS V8 engine.  Bundle...

[PN: 109-9000B] Link ECU G4X XtremeX ECU + Terminated LS Engine Harness Drive-by-Wire Bundle

Harness Manual Online Instruction Manual   The quickest, easiest, tidiest and most cost effective way to connect a Link ECU to your Drive-by-Wire/E-Throttle LS V8 engine.  Bundle Includes: ...

[PN: 110-0005] Link ECU Mounting bracket for G4+ & G4X Atom & Monsoon (MTB2)

[PN: 114-1000] Link ECU KnockLink G4 (G4KNL)

DETAILS:   KnockLink is a self-calibrating, visual knock warning tool. The KnockLink is designed for tuning, street and race use. Will require a knock sensor to function (sold separately) or...

[PN: 114-2000] Link ECU G4 KnockLink Kit - Includes Knock Sensor+Loom (G4KNLK)

DETAILS:   Kit includes the G4 KnockLink visual warning light and a knock sensor with loom. The KnockLink is a self-calibrating, visual knock warning tool. This kit is designed for tuning,...

[PN: 115-1000] Link ECU E-throttle (RET)

Wiring Diagram (Example) DETAILS: Link's external E-throttle (Drive by Wire) module works with Link's G4X ECUs (except the entry level AtomX), plus G4+ ECUs (Storm and above) to give you full...

[PN: 125-1000] Link ECU CAN Lambda (CANLAM)

Download the CAN-Lambda QuickStart Guide Download the CAN-Lambda manual DETAILS: Link’s CAN Lambda is an easy to use CAN module that provides digital wideband sensor control via CAN bus and is...

[PN:101-0002] Link ECU A Loom short (0LA)

DETAILS: 0.4m long 'A' loom to suit G4, G4+ and G4X Wire-In ECUsPerfect for all custom wiring jobs utilising Link WireIn ECUs. The ‘A’ Loom has a Link ‘A’ ECU connector at one...

[PN: 101-0165] Link ECU Link 4 Bar MAP Sensor (MAP4)

DETAILS:   The Link 4 Bar MAP sensor reads up to 4 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 3.0 Bar (or 44psi) of boost...